Computherm thermostat e230

The COMPUTHERM E280 Wi-Fi room thermostat is specifically designed to control heating and cooling systems. The thermostat connects your smartphone or tablet to the device you want to control remotely. With the E280, you can set the temperature of your home hour by hour and have the option to set and control it over the Internet.
The on/off switching of the controlled appliance allows you to ensure a constant, comfortable temperature while avoiding unnecessary energy losses. The product is particularly ideal if your apartment or house is not used according to a predetermined schedule, if you are away from home for an indefinite period during the heating season, or if you want to use your holiday home during the heating season.
The device can be easily controlled via the Internet and the touch button interface, and its operating status can be constantly monitored. The thermostat is particularly suitable for controlling underfloor heating systems thanks to the connectable floor temperature sensor. The thermostat is equipped with two potential-free relays that switch simultaneously, allowing the control of two completely independent products or the simple separation of a heating system into zones without the need for a separate zone controller.
In addition, the thermostat can also control electrical and electronic devices that can be switched on/off by removing and restoring power.

With the E280 you can set the temperature you want for all hours of the day and night. This way you will always have the temperature you need in your home. It provides comfort without wasting energy. You only use as much energy as you need, so you can save up to 30% on your heating bills. You can also save energy thanks to its remote control feature, which allows you to remotely switch off and switch back on the appliance you want to control in case of absence/travel.

COMPUTHERM E280 is a switch mode room thermostat suitable for the control of the vast majority of boilers and air conditioners on the market in Hungary. It can be easily connected to any gas boiler with a two-wire room thermostat connection point, as well as to any air conditioner or other electrical appliance, regardless of whether they have a 24 V or 230 V control circuit.

The E280 thermostat can also be used to control an air conditioner.

For products purchased before October 2020: if the cooling is controlled, the controlled refrigeration appliance must be wired as described in the user manual, other than in heating mode.

For products purchased after October 2020: if you want to control cooling, you must switch the thermostat to cooling mode in the app or by using the thermostat's touch buttons. In this case, the wiring does not need to be modified.

No, an air conditioning appliance that can be controlled by the device, or basically any appliance that can be operated in practice by its on/off function alone.

For products purchased before October 2020: If the cooling is controlled, the controlled refrigeration appliance must be wired as described in the operating instructions, other than in the heating mode.

For products purchased after October 2020: If you want to control cooling, you must switch the thermostat to cooling mode in the app or by using the thermostat's touch buttons. In this case, the wiring does not need to be modified.

No batteries are needed to operate the E280. A 230 V mains supply is required to operate the thermostat.

Any number of devices. Each E280 device you set up can be added to your phone app, making it controllable from your phone.

No. All thermostats are individually connected to the local Wi-Fi network, which guarantees safe, trouble-free operation of the devices. This means that essentially any number of devices can be used in close proximity to each other without causing any problems in communication between the devices.

Even without a Wi-Fi connection with Internet access, the device can be used with full functionality using the thermostat's touch buttons. However, you can only control the thermostat remotely if it is connected to a Wi-Fi network with Internet access.

The thermostat should be placed in the room where it is used regularly or for long periods of time, in the direction of the natural air movement in the room, but not exposed to drafts or extreme heat (e.g. sunlight, refrigerator, chimney, etc.). The optimum position is 0,75-1,5 m above floor level.
Using a floor temperature sensor, it is possible to control the output(s) based on the temperature measured by this sensor. On the other hand, it can be used to set a maximum temperature at which the thermostat will switch off the outputs. This function is particularly useful for floor and electric heating systems for safety reasons. If you wish to use the thermostat for floor temperature detection, it is recommended that the thermocouple is embedded in the floor in a short copper tube so that it can be easily replaced in case of failure.

No, only one floor temperature sensor can be connected to a device.

If the display reads Err (Er, Err), the set temperature sensor does not signal the thermostat. If the floor temperature sensor is not connected, select Built-in temperature sensor in the phone app or in the appliance menu under the Temperature sensor (SEN) function. If the floor sensor is connected, check that it is connected correctly.

The device has potential-free (de-energised) output connections, so that in normal operation the 230 V voltage does not appear at the outputs, but only closes the two connected wires or breaks the connection between them. If you want the device to have a 230 V mains voltage at its output when it is switched on, you must connect a mains phase wire to one of the connection points of the device as described in the operating instructions. Before connecting the phase wire, it is essential that the phase wire is disconnected from the mains and that the connection is carried out by a qualified person.

The temperature measured by the device can be calibrated, so that the display shows the modified temperature values. The calibration of the measured temperature can be done according to chapter 10.4 of the operating instructions.

If you can, move the router closer to the E280. Another option is to place a Wi-Fi signal booster between the router and the E280, which will increase the range of the router.

Download and view our Wi-Fi network connection suggestions document.

In the event that the product cannot be controlled via the Internet because the application says that the device is not available and the device does not respond to changes, the connection between the product and the web interface is broken. There are several possible reasons for this. The most likely problem is caused by the Wi-Fi router you are using. It is a good idea to restart routers from time to time by turning off the power and then turning it back on. In most cases, this will eliminate this type of problem. If after a few minutes the product is still unavailable on the control panel, it is recommended to reconnect the product to the Wi-Fi network as described in chapter 7.2 of the user manual. If the connection is successful but the product is still not available, it is recommended to reset the router to factory settings, as the settings may prevent the device from connecting to the Internet. As long as the thermostat is not accessible via the Internet, you can still control it manually using the thermostat's touch buttons.

The unit will not operate without power, but the thermostat can remember the settings. In the event of a power failure (power cut), it can continue to operate without any external intervention after the power supply is restored, if this option is selected in the settings (see chapter 10.6 of the user manual).

All thermostat settings except date and time will be reset to factory default as described in chapter 10.8 of the user manual.

If you use Android, you can download the app from the Google Play store. If you use iOS, you can download the app from the iTunes Store. The application is called COMPUTHERM E Series.